|
|
|
| Tri-City Lock Company's HOLE SAW ALIGNMENT GUIDES |
|
Hole Saw Alignment Guides available in 4 sizes:
-
1-1/2" overbores 1-1/2" hole incr. it to 2-1/8"
-
3/4" overbores 3/4" hole incr. it to 7/8" or 1"
-
5/8" overbores 5/8" hole incr. it to 7/8" or 1"
-
7/8" overbores 7/8" hole incr. it to size holesaw used
|
 |
| 3 Sizes of Hole Saw Alignment Guides inserted in holesaws |
|
|
| Tri-City Lock Company's Hole Saw Alignment Guides are revolutionizing the way we over-bore existing holes--whether the hole was drilled the wrong size or we just want to modernize an old lockset with a new one and need a bigger hole centered over the old one.
These Guides are easy to use and don't take as much time as the "old" ways. They'll save you time, money, and aggravation.
To use, insert Hole Saw Alignment Guide shaft into hole saw where pilot drill was, insert arbor into drill chuck, tighten up, and you're ready to drill. NO MEASURING CENTERS, NO ADJUSTING JIGS, NO "C" CLAMPS, AND NO PLYWOOD--JUST DRILL! |
| Hole Saw Alignment Guides...one by one |
| The 1-1/2" diameter Hole Saw Alignment Guide will enlarge a 1-1/2" diameter existing hole to 2-1/8" diameter or larger, depending on the size holesaw used. As you drill, the spring on the shaft keeps tension on the cone to keep it in place. To use, take out the pilot drill from the holesaw arbor, replace it with the Guide shaft, and tighten the setscrew. Put cone into existing hole, drill halfway from one side, and then drill from the opposite side to complete. |
| The 3/4" Hole Saw Alignment Guide enables you to enlarge an existing 3/4" diameter hole to 7/8" or 1" diameter, depending on the size holesaw used. An arbor (like the one shown to the left) should be used with the 3/4" Guide. Because the shaft of this Guide is much longer than the one used on the 1-1/2" Guide, an arbor where the shaft can go directly through to be inserted into the drill chuck must be used. The end of shaft is tri-beveled to fit into the drill's chuck so it won't slip while you drill. The door/cabinet/desk does not have to be drilled from both sides. |
|
The 7/8" Saw Alignment Guide enables you to enlarge an existing 7/8" diameter hole to a larger diameter, depending on the size holesaw used. A small arbor should be used with the 7/8" Guide. Because the shaft of this Guide is much longer than the one used on the 1-1/2" Guide, an arbor where the shaft can go directly through to be inserted into the drill chuck must be used. The end of shaft is tri-beveled to fit into the drill's chuck so it won't slip while you drill. The door/cabinet/desk does not have to be drilled from both sides.
|
| The 5/8" Hole Saw Alignment Guide enables you to enlarge an existing 5/8" diameter hole to 7/8" or 1" diameter, depending on the size holesaw used. An arbor (like the one shown to the left) should be used with the 5/8" Guide. Because the shaft of this Guide is much longer than the one used on the 1-1/2" Guide, an arbor where the shaft can go directly through to be inserted into the drill chuck must be used. The end of shaft is tri-beveled to fit into the drill's chuck so it won't slip while you drill. The door/cabinet/desk does not have to be drilled from both sides. |
HOLE SAW ALIGNMENT GUIDES
1-1/2" dia $49.50 each USD
3/4" dia $22.50 each USD
5/8" dia $22.50 each USD
7/8" dia $22.50 each USD
Arbor $9.95 each USD
Complete Set (1 each size Guide and 1 arbor) $119.50 USD
MONEY BACK GUARANTEE | EXTRAS:
ARBOR for 3/4", 7/8" and 5/8" diameter Guides $9.95 each USD
*USPS Priority, Insured, Delivery Receipt
Hole Saw Alignment Guides are sold WITHOUT holesaws
DISCOVER, MC & VISA ACCEPTED | SHIPPING & HANDLING
1 Guide in Cont. USA $8.75*USD
2 Guides in Cont. USA $9.75*USD
1 Set in Cont. USA $11.00*USD
Outside USA - CALL FOR QUOTE |
| ABOUT Tri-City Lock Company |
Daniel D. Mello, Owner-Locksmith
Tri-City Lock Company
20059 Pleasant View Drive
Groveland, California 95321
(209) 962-4692 Phone Fax (888)514-1009
E-mail: sharon@tricitylock.com OR slmello@aol.com
DISCOVER, MC & VISA ACCEPTED |
|
|
|
